Tanglewood Necklace Tutorial

Attach a TierraCast brass oxide pewter small dagger charm to the TierraCast brass oxide pewter reversible large Flora ring link using three 5.5mm antique brass-plated 21 gauge open jump rings linked together. Attach a TierraCast brass oxide pewter large dagger charm to the right of this charm using three jump rings linked together. Attach another small dagger charm to the right of the last charm using three jump rings linked together.

Opening and Closing Jump Rings Video

Slide a 6mm round pearl in Powder Almond onto a 1.5-inch antique brass-plated 23 gauge eye pin, followed by a TierraCast brass oxide pewter 5mm Tiffany bead cap, a 4mm round pearl in Crystal Iridescent Red, a bead cap, and another Powder Almond pearl. Make a simple loop at the top of the beads. Repeat this step for a total of two bead cap links.

Simple Loop Tutorial

Slide a Powder Almond pearl onto an eye pin, followed by three TierraCast brass oxide pewter small woodland beads, and another Powder Almond pearl. Make a simple loop at the top of the beads. Repeat this step for a total of two woodland bead links.

Cut a length of 4.5mm antique brass flat O-link chain approximately three O-links long. Attach it to the top of the ring link using a jump ring. Repeat for the other side of the necklace.

Open the loop of a bead cap dangle and attach it to the end of one chain. Close the loop. Repeat for the other side of the necklace.

Cut a length of chain approximately five O-links long. Open the loop of the link on one side of the necklace and attach the chain. Close the loop. Repeat for the other side of the necklace.

Open the loop of a woodland bead link and attach it to the end of the chain on one side of the necklace. Close the loop. Repeat for the other side of the necklace.

Cut a length of chain approximately six inches long. Attach it to the link on one side of the necklace. Repeat for the other side of the necklace. Attach the TierraCast brass oxide pewter heirloom clasp set to each end of the necklace using a jump ring for each.

Cut a length of chain five O-links long. Attach one end to the center O-link of the chain section between the two beaded links on one side of the necklace using a jump ring. Attach the other end to the corresponding O-link on the other side of the necklace using a jump ring.

Attach the TierraCast brass oxide pewter reversible Floral petal to the center O-link of this chain using a jump ring

List of Components
TierraCast Brass Oxide Pewter Reversible Large Flora Ring Link (BRO-3200, qty 1)
TierraCast Brass Oxide Pewter Small Dagger Charm (BO-2510, qty 2)
TierraCast Brass Oxide Pewter Reversible Flora Petal (BRO-2493, qty 1)
TierraCast Brass Oxide Pewter Small Woodland Bead (BRO-5649, qty 6)
TierraCast Brass Oxide Pewter 5mm Tiffany Bead Cap (BRO-5578, qty 4)
5810 6mm Round Pearl Powder Almond (5810-PALM6, qty 8)
5810 4mm Round Pearl Crystal Iridescent Red (5810-CIR4, qty 2)
4.5mm Antique Brass Flat O-Link Chain By the Foot (BTF-0950, qty 2)
TierraCast Brass Oxide Pewter Heirloom Clasp Set (BRO-6070, qty 1)
1.5-inch Antique Brass-Plated 23 Gauge Eye Pin (BBA-EP15-24, qty 4)
5.5mm Antique Brass-Plated 21 Gauge Open Jump Ring (BBA-OJR06-A, qty 16)
TierraCast Brass Oxide Pewter Large Dagger Charm (BO-2511, qty 1)