This wide ribbon belt is a great way to add a special touch to a dress. The crystal accents in the back double as snaps to hold it in place.
Add a subtle blue accent to your wedding dress by wearing an elegant belt decorated sparingly with sparkling crystal components. With its layered bow design topped off with an iridescent crystal, this quick project is the perfect way to incorporate some color into your wedding ensemble.
Measure your waist (or the waist of whoever will be wearing this belt) and cut a length of ribbon to match that length. Make sure to add three inches or so to accommodate for folds on the ends and any overlap. We used a wide Tiffany blue ribbon with a subtle gold luster.
Fold the edges over on one end about an inch and stitch the bottom and top edges where the ends of the folded edge and the rest of the belt meet.
On the other end of the belt, fold the edge over toward the front of the belt, about 1 1/2 inches. Fold the edge of that fold in and under itself about a half an inch or so and stitch the under-fold to the belt.
Use a crystal applicator handheld tool to apply two 11mm gold-plated flatback snap fasteners in Crystal AB to both ends of the belt, on the top and bottom of the folded edges. The decorative fasteners will be attached on top of the fold from step three. The snap studs should be facing the same direction as the flatback fasteners.
Cut a length of ribbon about 30 inches long. Lay the right edge down in the center of your belt. Measure out more ribbon about four inches to the left of where you placed the edge in the last step, place your finger on top of the ribbon and fold the rest of the ribbon over your finger.
Measure out more ribbon to the right of that fold, about 6 1/2 inches, place your finger there and fold over your finger again in the opposite direction. Measure about 2 1/2 inches to the left of this fold and stitch these layers to your belt.
From the stitch you just made, measure out ribbon about 4 inches to the left, place your finger and fold the ribbon over. Make sure this fold is half an inch shorter on both sides than the previous layer.
Keep folding the ribbon over in opposite directions, always making sure the next layer is half an inch shorter than the previous layer on both sides. Do this to create two more ribbon layers.
Create a small ribbon loop on top of these layers and in the center of your belt by folding the edge of the ribbon in and under itself. This loop should be about an inch wide.
Secure all of these ribbon layers by attaching the 17mm gold-plated large flatback jeans button in Crystal AB to the center of the bow design. Make sure this button goes through all of the layers of the bow by cutting a slit with a blade for the shank of the button to fit through.
Finish by stitching the bottom layer of the bow to the belt, about 1 1/2 inches to the left of where you stitched the first layers in step six.
List of Components: 1790140 17mm Gold-Plated Large Flatback Jeans Button Crystal AB (1790G140-CAB17, qty 1) 1780100 11mm Gold-Plated Flatback Snap Fastener Crystal AB (1780G100-CAB11, qty 1)
Add all available items to your cart at once or edit the quantities below.
Any items with quantities lower than stated minimums will default to the minimum in your cart.
Nice choice! All or most of the products needed for this project are shown
below with quantities. Sometimes we sell out of components and aren’t able to order more from
the manufacturer (we know, it is very disappointing to us, too). Use the opportunity to mix up
the design and make it yours by substituting similar products or altering the entire color
scheme—it’s up to you!
Please wait while we add the products to your cart.
Tie A Beau
DIY Blue Bow Belt
designed byArtbeads
Skill LevelBeginner
TechniqueCrimps, Bails & Connectors
Time1-3 Hours
This wide ribbon belt is a great way to add a special touch to a dress. The crystal accents in the back double as snaps to hold it in place.
Add a subtle blue accent to your wedding dress by wearing an elegant belt decorated sparingly with sparkling crystal components. With its layered bow design topped off with an iridescent crystal, this quick project is the perfect way to incorporate some color into your wedding ensemble.
Supplies
Step-by-Step Instructions
Measure your waist (or the waist of whoever will be wearing this belt) and cut a length of ribbon to match that length. Make sure to add three inches or so to accommodate for folds on the ends and any overlap. We used a wide Tiffany blue ribbon with a subtle gold luster.
Fold the edges over on one end about an inch and stitch the bottom and top edges where the ends of the folded edge and the rest of the belt meet.
On the other end of the belt, fold the edge over toward the front of the belt, about 1 1/2 inches. Fold the edge of that fold in and under itself about a half an inch or so and stitch the under-fold to the belt.
Use a crystal applicator handheld tool to apply two 11mm gold-plated flatback snap fasteners in Crystal AB to both ends of the belt, on the top and bottom of the folded edges. The decorative fasteners will be attached on top of the fold from step three. The snap studs should be facing the same direction as the flatback fasteners.
Cut a length of ribbon about 30 inches long. Lay the right edge down in the center of your belt. Measure out more ribbon about four inches to the left of where you placed the edge in the last step, place your finger on top of the ribbon and fold the rest of the ribbon over your finger.
Measure out more ribbon to the right of that fold, about 6 1/2 inches, place your finger there and fold over your finger again in the opposite direction. Measure about 2 1/2 inches to the left of this fold and stitch these layers to your belt.
From the stitch you just made, measure out ribbon about 4 inches to the left, place your finger and fold the ribbon over. Make sure this fold is half an inch shorter on both sides than the previous layer.
Keep folding the ribbon over in opposite directions, always making sure the next layer is half an inch shorter than the previous layer on both sides. Do this to create two more ribbon layers.
Create a small ribbon loop on top of these layers and in the center of your belt by folding the edge of the ribbon in and under itself. This loop should be about an inch wide.
Secure all of these ribbon layers by attaching the 17mm gold-plated large flatback jeans button in Crystal AB to the center of the bow design. Make sure this button goes through all of the layers of the bow by cutting a slit with a blade for the shank of the button to fit through.
Finish by stitching the bottom layer of the bow to the belt, about 1 1/2 inches to the left of where you stitched the first layers in step six.
List of Components: 1790140 17mm Gold-Plated Large Flatback Jeans Button Crystal AB (1790G140-CAB17, qty 1) 1780100 11mm Gold-Plated Flatback Snap Fastener Crystal AB (1780G100-CAB11, qty 1)